Extrusion is the process by which long straight metal parts can be produced. The cross-sections that can be produced vary from solid round, rectangular, to L shapes, T shapes. Tubes and many other different types. Extrusion is done by squeezing metal in a closed cavity through a tool, known as a die using either a mechanical or hydraulic press.

Extrusion Processing

Extrusion produces compressive and shear forces in the stock. No tensile is produced, which makes high deformation possible without tearing the metal. The cavity in which the raw material is contained is lined with a wear resistant material. This can withstand the high radial loads that are created when the material is pushed the die.

The Simple Extrusion Diagram

Extrusion is a process used to create objects of a fixed cross-sectional profile. A material is pushed or drawn through a die of the desired cross-section. The two main advantages of this process over other manufacturing processes are its ability to create very complex cross-sections and work materials that are brittle, because the material only encounters compressive and shear stresses. It also forms finished parts with an excellent surface finish.

PVC Extrusion Dies

Extrusion may be continuous (theoretically producing indefinitely long material) or semi-continuous (producing many pieces). The extrusion process can be done with the material hot or cold.Commonly extruded materials include metals, polymers, ceramics, concrete and foodstuffs. Hollow cavities within extruded material cannot be produced using a simple flat extrusion die, because there would be no way to support the center barrier of the die. Instead, the die assumes the shape of a block with depth, beginning first with a shape profile that supports the center section. The die shape then internally changes along its length into the final shape, with the suspended center pieces supported from the back of the die.

Direct and Indirect Extrusion

Extrusions, often minimize the need for secondary machining, but are not of the same dimensional accuracy or surface finish as machined parts. Surface finish for steel is 3 µm; (125 µ in), and Aluminum and Magnesium is 0.8 µm (30 µ in). However, this process can produce a wide variety of cross-sections that are hard to produce cost-effectively using other methods. Minimum thickness of steel is about 3 mm (0.120 in), whereas Aluminum and Magnesium is about 1mm (0.040 in). Minimum cross sections are 250 mm2 (0.4 in2) for steel and less than that for Aluminum and Magnesium. Minimum corner and fillet radii are 0.4 mm (0.015 in) for Aluminum and Magnesium, and for steel, the minimum corner radius is 0.8mm(0.030 in) and 4 mm (0.120 in) fillet radius.

Aluminum Extrusion Dies

Cold Extrusion :

Cold extrusion is the process done at room temperature or slightly elevated temperatures. This process can be used for most materials-subject to designing robust enough tooling that can withstand the stresses created by extrusion. Examples of the metals that can be extruded are lead, tin, aluminum alloys, copper, titanium, molybdenum, vanadium, steel. Examples of parts that are cold extruded are collapsible tubes, aluminum cans, cylinders, gear blanks.

The advantages of cold extrusion are:

  • No oxidation takes place.
  • Good mechanical properties due to severe cold working as long as the temperatures created are below the re-crystallization temperature.
  • Good surface finish with the use of proper lubricants.

Hot Extrusion :

Hot extrusion is done at fairly high temperatures, approximately 50 to 75 % of the melting point of the metal. The pressures can range from 35-700 MPa (5076 - 101,525 psi). Due to the high temperatures and pressures and its detrimental effect on the die life as well as other components, good lubrication is necessary.

Hot Extrusion Process

Oil and graphite work at lower temperatures, whereas at higher temperatures glass powder is used. Typical parts produced by extrusions are trim parts used in automotive and construction applications, window frame members, railings, aircraft structural parts.

References :

  • http://www.efunda.com/
  • http://en.wikipedia.org/
  • http://engr.bd.psu.edu/
  • http://gadgetflash.com/
  • http://gadgetflashstore.com/

You might also like

How Aluminum is Produced   Aluminum manufacture is accomplished...
Foundry and Casting   A foundry is a factory that produces...
Cast Iron   Cast iron is derived from pig iron,...
Aluminum alloy Aluminum Alloy Wheel An alloy is a material...
Grab This Widget
METALLURGY CORNER

Random Posts

  • Whai is Stainless Steel?
    Stainless steel is the name given to a group of corrosion resistant and high temperature steels. Their remarkable resist...
  • Types of Materials
    Metals are elements that generally have good electrical and thermal conductivity.Many metals have high strength, high st...
  • Titanium and It’s Alloys
    Titanium was discovered in Cornwall, England, by William Gregor in 1791 and named by Martin Heinrich Klaproth for the Ti...
  • Semiconductor Materials
    A semiconductor is a substance, usually a solid chemical element or compound, that can conduct electricity under some co...
  • Welding
    Welding is a fabrication or sculptural process that joins materials, usually metals or thermoplastics, by causing coales...